Rubber Tire ATV Mounted Drills | Truck Mounted Drills | Track Carrier Mounted Drills | Trailer Mounted Drills | Skid Mounted Drills
85 Features | 85 Specifications | 85 Optional Equipment
Hydraulic rod holder and breakout wrench†
The hydraulic rod holder makes your job quicker and safer. It not only pivots from on-hole to off-hole positions, but also hydraulically moves in and out. For efficient operation, the breakout wrench is mounted at the pivot point of the rod holder arm. Systems available up to 6 5/8 inch (16.8 cm) capacity. Adjustable height is also available.
Our 140 pound (63.5 kg) automatic hammer gives you extremely consistent and accurate Standard Penetration Test results, meeting all ASTM-D-1586 requirements. That’s because there are no ropes or cables to impede the free fall of the weight. The hammer swings from stored position to on-hole position. Since raising and lowering is done hydraulically, set up is quick and almost effortless. For maximum safety, all moving parts are enclosed, including the impact area between the weight and the anvil. Other hammer sizes available including 170 pound (77.1 kg), 300 pound (136.1 kg), and 340 pound (154.2 kg).
Quick mast disconnect†
This feature allows you to quickly disconnect the mast when working inside buildings, underneath bridges or in other low overhead drilling locations. Since the mast is completely separated from the upright, it doesn’t interfere with other drill functions such as the in-out slide base. With the mast in the horizontal position, you simply clamp it to its storage rack and extend the drill’s in-out slide base. This pulls the sockets on the upright drill frame away from the large tapered pins on the mast.
Patented angle drilling system†
This unique system is especially effective for drilling underneath ponds, storage tanks, or other structures. When used with our patented continuous sample tube system, you can even take soil samples while drilling angle holes. The angle drilling system will also allow you to drill vertically with the carrier positioned on an uphill slope. That can eliminate the time-consuming job of leveling the rig. And, since the kelly drive is always coupled to the right angle drive box, you can raise and lower the mast with the drivetrain already connected and ready to go.
Fluted kelly and chuck assembly†
If your drilling operations include a substantial amount of rotary or core drilling, the CME fluted kelly and chuck assembly can save you alot of time. The 5 foot (1.5 m) stroke of the kelly combined with 6 foot (1.8 m) stroke of the feed system, gives you a total stroke of 11 feet (3.4 m). You can use 10 foot (3 m) drill rods, which means fewer rod connections and less rod handling. The kelly has two vertical slots (flutes) and two sets of horizontal slots which are engaged by the chuck to provide rotary torque and thrust. The CME fluted kelly can even be rotated without engaging the thrust keys. This gives you the option of using the weight of the drill string to provide down pressure on the bit. The 2 5/8 inch (6.7 cm) fluted kelly and chuck assembly is available in either manual or hydraulic actuated configurations. For drilling larger diameter holes, a 3 1/2 inch (8.9 cm) O.D. fluted kelly and hydraulic chuck assembly is available.
Water tank / tool box combination
A 330 gallon (1,249 L) stainless steel water tank is available that includes 18 inch (45 cm) deep tool boxes on each side. The tool boxes have removable shelves and lockable swing out doors. Numerous other water tank/tool box configurations are available, including models with rod storage underneath and open storage on top.
Cone Penetrometer Testing (CPT)
CPT controls allow you to easily switch from typical geotechnical drilling and sampling procedures to pushing a cone. A dedicated hydraulic circuit including detented CPT control lever, hydraulic down feed pressure and CPT feed rate controls provide precise pressure and penetration adjustments required to meet ASTM standards. A separate CPT system hydraulic pressure gauge is provided as well. Anchor points are installed below the drill feed frame so that maximum available pressure can be applied to the CPT tools. A 12-volt power source can be provided at the drill control panel to accommodate electronic devices associated with CPT procedures. Mounting for depth transducers or other related equipment can also be provided.
Additional optional equipment
† Patented by Central Mine Equipment Company
Performance ratings are based on engineering specifications, calculations and accepted industry standards.
Capacities may vary according to drilling conditions. CME reserves the right to amend these specifications at any time, without notice.
Call 1-800-325-8827 for more information!
Home | Request-a-Quote | About Us | Contact Us | Product Support Team | Drill Rigs | Hollow Stem Augers | Continuous Flight Augers | Continuous Sample Tube Systems | Support Equipment | Tooling & Supplies
Rig Repair & Upgrades | Product Line | Product Catalog | Brochures | Sign Up for Monthly Product Updates | Product Update Archives | Upcoming Events | Privacy Statement | Sitemap
Copyright© 2021. Central Mine Equipment Company. A Missouri Corporation. All rights reserved.
4215 Rider Trail North · Earth City, MO 63045 · (800) 325-8827 · (314) 291-7700 · Fax (314) 291-4880 · firstname.lastname@example.org · www.cmeco.com
8:00 a.m. - 4:30 p.m. Central Time
Proudly made in the U.S.A. since 1928.