REQUEST-A-QUOTE PRODUCT CATALOG SIGN UP FOR
PRODUCT UPDATES

CME-850XR Brochure	CME Product Catalog

Hydraulic rod holder and breakout wrench^†

The hydraulic rod holder makes your job quicker and safer. It not only pivots from on-hole to off-hole positions, but also hydraulically moves in and out. For efficient operation, the breakout wrench is mounted at the pivot point of the rod holder arm. Systems available up to 6-5/8 inch (16.8 cm) capacity.

Automatic hammer^†

The CME 140 pound (63.5 kg) automatic hammer has become the industry standard. It gives you extremely consistent and accurate Standard Penetration Test results, meeting all ASTM-D-1586 requirements. That’s because there are no ropes or cables to impede the free fall of the weight. The hammer swings from stored position to on-hole position. Since raising and lowering is done hydraulically, set up is quick and almost effortless. For maximum safety, all moving parts are enclosed, including the impact area between the weight and the anvil. Other hammer systems are available including a 170 pound (77 kg), 300 pound (136 kg), and 340 pound (154 kg).

Quick mast disconnect^†

This feature allows you to quickly disconnect the mast when working inside buildings, underneath bridges or in other low overhead drilling locations. Since the mast is completely separated from the upright, it doesn’t interfere with other drill functions such as the in-out slide base. With the mast in the horizontal position, you simply clamp it to its storage rack and extend the drill’s in-out slide base. This pulls the sockets on the upright drill frame away from the large tapered pins on the mast.

All-weather cab — ROPS Certified

For severe weather conditions, the CME-850X can be equipped with an all-weather ROPS cab. This cab is insulated and includes such features as an efficient heater, a defroster, a roll down left window and a windshield wiper.

Fluted kelly and chuck assembly^†

If your drilling operations include a substantial amount of rotary or core drilling, the CME fluted kelly and chuck assembly can save you a lot of time. The 5 foot (1.5 m) stroke of the kelly combined with the 6 foot (1.8 m) stroke of the feed system, gives you a total stroke of 11 feet (3.4 m). You can use 10 foot (3 m) drill rods, which means fewer rod connections and less rod handling. The kelly has two vertical slots (flutes) and two sets of horizontal slots which are engaged by the chuck to provide rotary torque and thrust. The CME fluted kelly can even be rotated without engaging the thrust keys. This gives you the option of using the weight of the drill string to provide down pressure on the bit. The 2-5/8 inch (6.7 cm) fluted kelly and chuck assembly is available in either manual or hydraulic actuated configurations. Or if you are drilling larger diameter holes, a 3-1/2 inch (8.9 cm) O.D. fluted kelly and hydraulic chuck assembly is available.

Cone Penetrometer Testing (CPT)

CPT controls allow you to easily switch from typical geotechnical drilling and sampling procedures to pushing a cone. A dedicated hydraulic circuit including detented CPT control lever, hydraulic down feed pressure and CPT feed rate controls provide precise pressure and penetration adjustments required to meet ASTM standards. A separate CPT system hydraulic pressure gauge is provided as well. Anchor points are installed below the drill feed frame so that maximum available pressure can be applied to the CPT tools. A 12-volt power source can be provided at the drill control panel to accommodate electronic devices associated with CPT procedures. Mounting for depth transducers or other related equipment can also be provided.

Additional optional equipment

• Water tank
• Work table, pipe vise options
• Auger and rod guides for angle drilling
• Stabilized water swivel
• Additional tool boxes available
• Spindle adapter
• Utility air tool system
• Cathead
• Hydraulic hoist
  • 1,800 pound (816 kg)
  • 3,200 pound (1,452 kg)
  • 7,000 pound (3,175 kg)
  • 8,500 pound (3,855 kg)
• Hydraulic wireline hoist
  • 1,800 pound (816 kg), max line speed 200 ft./min (61 m/min)
  • 900 pound (408 kg), max line speed 400 ft./min (122 m/min)
• Water pumps
  • Moyno 3L6 36 gpm/225 psi (136 lpm/1,551 kPa)
  • Moyno 3L8 84 gpm/225 psi (318 lpm/1,551 kPa)
  • Bean L09 (420) 25 gpm/500 psi (95 lpm/3,448 kPa)
  • Bean L1122 (435) 35 gpm/500 psi (132 lpm/3,448 kPa)
  • Other pumps available

† Patented by Central Mine Equipment Company

850XR Features  |  850XR Specifications  |  850XR Optional Equipment

Performance ratings are based on engineering specifications, calculations and accepted industry standards.
Capacities may vary according to drilling conditions. CME reserves the right to amend these specifications at any time, without notice.