Rubber Tire ATV Mounted Drills | Truck Mounted Drills | Track Carrier Mounted Drills | Trailer Mounted Drills | Skid Mounted Drills
55LCX/300 Features | 55LCX/300 Specifications | 55LCX/300 Optional Equipment
Low clearance, even higher performance
The CME-55LCX/300 offers the versatility of the CME-55LC/300 with about 27% more spindle torque. It has a full length mast for typical everyday site conditions. But when overhead space is limited, you can easily change over to low clearance mode. The CME-55LCX/300 can set up and drill in a little as 12 foot, 1 inch (3.68 m) overhead clearance. And you still have the full 72 inch (183 cm) feed stroke, low clearance sheaves permit full use of hoist lines and the low clearance lifting cylinder allows for normal automatic hammer operation.
Quick disconnect mast
The quick disconnect mast can be secured in its storage rack and removed from the drill by simply sliding the drill back with the hydraulic in/out slide base control. “Quick-cabling” sheaves allow you to easily move the hoist lines from the mast sheaves to the low clearance sheaves provided above the drill frame.
The CME-55LCX spindle torque rating of nearly 12,000 ft/lbs (16,270 Nm) comes from a 130 horsepower Cummins QSF 3.8 turbocharged diesel engine. This new engine is U.S. EPA tier-4 final certified, includes cold weather starting aid and engine protection shutdown systems.
CME designed track carrier for CME drills
Like every CME all-terrain and rough-terrain drill, the CME-55LCX/300 track drill uses a single engine power source. This means lower operating costs and less time maintaining the machine. And since the CME-300 carrier is designed and built by CME specifically for CME drills, there are no compromises. Weight is evenly distributed across the carrier. We take full advantage of all available space, and consideration is given for practical use of the machine including approach angle for loading and unloading and for negotiating hilly terrain.
Remote control carrier
Remote control track drive, engine throttle and front carrier winch allow the operator to move freely around the machine. Manual back-up controls are provided for emergency use. Removable steel belly pans provide protection every day and access when needed. Rubber tracks won’t damage pavement.
Plenty of tool storage available
The CME-55LCX/300 track drill includes a front auger rack, drill rod rack and two tool boxes. Additional tool boxes, rod racks and other deck options are available. A water tank is offered as well.
Hydraulic feed system with fast retract
The hydraulic feed system provides 27,615 pounds (12,526 kg) of retract force and 19,750 pounds (8,958 kg) of down pressure. The fast retract speed of up to 95 ft/min (29 m/min) means more production. The split slide bushings are easily replaced after normal wear intervals, and the standard upright gives you the clearance to drill with up to 10-1/4 inch hollow augers.
Drill sliding base, in-out and sideways
Both in-out and sideways slide bases are standard equipment on the CME-55LCX/300 track drill. An 18 inch (45.7 cm) in-out slide allows you to quickly move the drill on and off the borehole and align the sheaves for lifting tools with the cathead or any of the hoists. A 6 inch (15.2 cm) sideways slide gives you even more versatility. Aligning augers or rods when making connections is easy. If the bit drifts off at an angle when you start a hole, you can quickly straighten it to a vertical position. Since the upright and mast are mounted directly to the drill frame, they move with the drill when the slide base is used.
Patented Spindle Brake stops rotation in an instant†
Our emergency Spindle Brake can stop rotation in less than a revolution. The system is activated by two conveniently located push button switches as well as strategically located multi-directional wobble switches.
† Patented by Central Mine Equipment Company
Performance ratings are based on engineering specifications, calculations and accepted industry standards.
Capacities may vary according to drilling conditions. CME reserves the right to amend these specifications at any time, without notice.
Call 1-800-325-8827 for more information!
Home | Request-a-Quote | About Us | Contact Us | Product Support Team | Drill Rigs | Hollow Stem Augers | Continuous Flight Augers | Continuous Sample Tube Systems | Support Equipment | Tooling & Supplies
Rig Repair & Upgrades | Product Line | Product Catalog | Brochures | Sign Up for Monthly Product Updates | Product Update Archives | Upcoming Events | Privacy Statement | Sitemap
Copyright© 2021. Central Mine Equipment Company. A Missouri Corporation. All rights reserved.
4215 Rider Trail North · Earth City, MO 63045 · (800) 325-8827 · (314) 291-7700 · Fax (314) 291-4880 · email@example.com · www.cmeco.com
8:00 a.m. - 4:30 p.m. Central Time
Proudly made in the U.S.A. since 1928.