Central Mine Equipment Company Drilling Rigs

HOME

ABOUT US

CONTACT US
  PRODUCT
SUPPORT TEAM

DRILL RIGS
HOLLOW
STEM AUGERS
SUPPORT
EQUIPMENT
PRODUCT
CATALOG
RIG REPAIR
& UPGRADES
PRODUCT
UPDATES
UPCOMING
EVENTS


CME-55/300 Rubber Track
Drill Optional Equipment




Rubber Tire ATV Mounted Drills  |  Truck Mounted Drills  |  Track Carrier Mounted Drills  |  Trailer Mounted Drills  |  Skid Mounted Drills



CME-55/300 Brochure CME Product Catalog

CME-55/300 Brochure

CME Product Catalog


55/300 Features  |  55 Specifications  |  55/300 Optional Equipment

Hydraulic rod holder and breakout wrench

CME-55/300 Track Mounted Drill Rod HolderThe hydraulic rod holder makes your job quicker and safer. It not only pivots from on-hole to off-hole positions, but also hydraulically moves in and out. For efficient operation, the breakout wrench is mounted at the pivot point of the rod holder arm. Systems available up to 6-5/8 inch (16.8 cm) capacity.


Automatic SPT hammer

Our 140 pound (63.5 kg) automatic hammer gives you extremely consistent and accurate Standard Penetration Test results, meeting all ASTM-D-1586 requirements. That’s because there are no ropes or cables to impede the free fall of the weight. The hammer swings from stored position to on-hole position. Since raising and lowering is done hydraulically, set up is quick and almost effortless. For maximum safety, all moving parts are enclosed, including the impact area between the weight and the anvil. Other hammer systems available including 170 pound (77 kg), 300 pound (136 kg), and 340 pound (154 kg).


Quick mast disconnect

This feature allows you to quickly disconnect the mast when working inside buildings, underneath bridges or in other low overhead drilling locations. Since the mast is completely separated from the upright, it doesn’t interfere with other drill functions such as the in-out slide base. With the mast in the horizontal position, you simply clamp it to its storage rack and extend the drills in-out slide base. This pulls the sockets on the upright drill frame away from the large tapered pins on the mast.


Angle drilling system for special applications

CME-55/300 Track Mounted DrillThis unique system allows you to drill holes at various angles between horizontal and vertical. It is especially effective for drilling under ponds, storage tanks or other structures. When used with our patented Continuous Sample Tube System, you can even take soil samples while drilling angle holes. The angle drilling system will also allow you to drill vertically with the rig positioned on an uphill slope. That can eliminate the time consuming job of leveling the rig. Since the kelly drive is directly connected to the right angle drive box, you can raise and lower the mast with the drivetrain already connected and ready to go.


Cone Penetrometer Testing (CPT)

CPT controls allow you to easily switch from typical geotechnical drilling and sampling procedures to pushing a cone. A dedicated hydraulic circuit including detented CPT control lever, hydraulic down feed pressure and CPT feed rate controls provide precise pressure and penetration adjustments required to meet ASTM standards. A separate CPT system hydraulic pressure gauge is provided as well. Anchor points are installed below the drill feed frame so that maximum available pressure can be applied to the CPT tools. A 12-volt power source can be provided at the drill control panel to accommodate electronic devices associated with CPT procedures. Mounting for depth transducers or other related equipment can also be provided.


Additional optional equipment

CME-55/300 Track Mounted Auger Rack Telescoping

CME-55/300 Track Mounted Drill Rig Mast Up



† Patented by Central Mine Equipment Company

55/300 Features  |  55 Specifications  |  55/300 Optional Equipment


Performance ratings are based on engineering specifications, calculations and accepted industry standards.
Capacities may vary according to drilling conditions. CME reserves the right to amend these specifications at any time, without notice.


Call 1-800-325-8827 for more information!



Home  |  Request-a-Quote  |  About Us  |  Contact Us  |  Product Support Team  |  Drill Rigs  |  Hollow Stem Augers  |  Continuous Flight Augers  |  Continuous Sample Tube Systems  |  Support Equipment  |  Tooling & Supplies

Rig Repair & Upgrades  |  Product Line  |  CME Product Catalog  |  Brochures  |  Sign Up for Monthly Product Updates  |  Product Update Archives  |  Upcoming Events  |  Privacy Statement  |  Sitemap

Rubber Tire ATV Mounted Drills  |  Truck Mounted Drills  |  Track Mounted Drills  |  Trailer Mounted Drills  |  Skid Mounted Drills


Copyright© 2024. Central Mine Equipment Company. A Missouri Corporation. All rights reserved.

4215 Rider Trail North · Earth City, MO 63045 · (800) 325-8827 · (314) 291-7700 · Fax (314) 291-4880 · info@cmeco.com · www.cmeco.com

8:00 a.m. - 4:30 p.m. Central Time (CT)

Proudly made in the U.S.A. since 1928. U.S. Flag

CME Facebook Page

CME is a proud member of the National Drilling Association CME is a proud member of the National Groundwater Association