CME-85 Truck Mounted Auger Drill Optional Equipment

CME-85 Truck Mount

Features | Specifications | Optional Equipment

 

CME-85 Hydraulic Rod HolderHydraulic rod holder and breakout wrench

The hydraulic rod holder makes your job quicker and safer. It not only pivots from on-hole to off-hole positions, but also hydraulically moves in and out. For efficient operation, the breakout wrench is mounted at the pivot point of the rod holder arm.

CME-85 Automatic SPT HammerAutomatic hammer

Our 140 pound [63.5 kg] automatic hammer gives you extremely consistent and accurate Standard Penetration Test results, meeting all ASTM-D-1586 requirements. That’s because there are no ropes or cables to impede the free fall of the weight.

The hammer swings from stored position to on-hole position. Since raising and lowering is done hydraulically, set up is quick and almost effortless.

For maximum safety, all moving parts are enclosed, including the impact area between the weight and the anvil. A 340/140 pound [154/63.5 kg] hammer is also available.

Quick mast disconnect

This feature allows you to quickly disconnect the mast when working inside buildings, underneath bridges or in other low overhead drilling locations. Since the mast is completely separated from the upright, is doesn’t interfere with other drill functions such as the in-out slide base.

With the mast in the horizontal position, you simply clamp it to its storage rack and extend the drill’s in-out slide base. This pulls the sockets on the upright drill frame away from the large tapered pins on the mast.

Patented angle drilling system

This unique system is especially effective for drilling underneath ponds, storage tanks, or other structures. When used with our patented continuous sample tube system, you can even take soil samples while drilling angle holes.

The angle drilling system will also allow you to drill vertically with the carrier positioned on an uphill slope. That can eliminate the time-consuming job of leveling an area on which to place the rig.

And, since the kelly drive is directly connected to the right angle drive box, you can raise and lower the mast with the drivetrain already connected and ready to go.

Fluted kelly and chuck assembly

If your drilling operations include a substantial amount of rotary or core drilling, the CME fluted kelly and chuck assembly can save you alot of time. The 5 foot [1.5 m] stroke of the kelly combined with 6 foot [1.8 m] stroke of the feed system, gives you a total stroke of 11 feet [3.4 m]. You can use 10 foot [3 m] drill rods, which means fewer rod connections and less rod handling.

The kelly has two vertical slots (flutes) and two sets of horizontal slots which are engaged by the chuck to provide rotary torque and thrust. The CME fluted kelly can even be rotated without engaging the thrust keys. This gives you the option of using the weight of the drill string to provide down pressure on the bit.

The 2 5/8 inch [6.7 cm] fluted kelly and chuck assembly is available in either manual or hydraulic actuated configurations. Or if you are drilling larger diameter holes, a 3 1/2 inch [8.9 cm] O.D. fluted kelly and hydraulic chuck assembly is available.

CME-85 ToolboxWater tank / tool box combination

A 330 gallon [1,249 L] stainless steel water tank includes 18 inch [45.5 cm] deep tool boxes on each side. For added convenience, removable shelves and lockable swing out doors.

Numerous water tank/tool box configurations are available, including models with rod storage capacity underneath and an expanded metal rack on top.

Additional optional equipment

  • Drill platform
  • Continuous sample tube system
  • High Speed Rotary Box
    • 18,000 foot pounds [24,480 Nm] max
    • 670 rpm max
  • Auger and rod guides for angle drilling
  • Quick mast disconnect
  • Dual pipe vises
  • Spindle adapter
  • Cathead, 8 inch [20.3 cm] diameter
  • Hydraulic hoist
    • 2,250 pound [1,021 kg], max line speed 200 ft./min [61 m/min]
    • 4,000 pound [1,814], max line speed 100 ft./min [30.5 m/min]
    • 8,500 pound [3,856 kg]
      • Up max line speed 87 ft./min [26.5 m/min]
      • Down max line speed 374 ft./min [114 m/min]
    • 10,000 pound [4,536 kg]
      • Up max line speed 72 ft./min [23 m/min]
      • Down max line speed 310 ft./min [94 m/min]
  • Hydraulic wireline hoist
    • 2,250 pound [1,021 kg], max line speed 200 ft./min [61 m/min]
  • Water pumps
    • Progressing cavity
      • 36 gpm/225 psi [136 lpm/1,551 kPa]
      • 84 gpm/225 psi [318 lpm/1,551 kPa]
    • Triplex piston
      • 40 gpm/800 psi [151 lpm/5,515 kPa]
    • Duplex piston
      • 148 gpm/197 psi [560 lpm/1,358 kPa]
    • Other pumps available

† Patented by Central Mine Equipment Company